Short answer: zdSCADA is a cloud-hosted SCADA platform built for oil and gas, now owned by Quorum Software. It connects to the RTUs, PLCs, meters and controllers already on your sites and lets you watch and control them from a browser or phone. If you need remote control and shutdowns, it is a strong pick. If you only need to see tank levels, pressures and whether the compressor is running, that is a lot of system to buy. TinyPumper watches all three on one wireless gateway, and your team installs it in 8 minutes.
The pumper pulls up at 7 a.m. and the compressor has been down since midnight. Nobody needed to shut a valve from the office. Somebody just needed to know. That is the line this page draws.
Is zdSCADA or TinyPumper the Better Fit for My Lease?
It depends on whether you need to control the site or see it. If your sites already run RTUs and PLCs and you need remote valve control or emergency shutdowns, zdSCADA fits. If you need tank levels, pressures and runtime on conventional wells with no controls staff, TinyPumper fits better. As of October 2026, TinyPumper is $349 per sensor, one time, plus one flat monthly rate per site, unlimited sensors. zdSCADA does not publish prices; it quotes each job (zdSCADA website, October 2026).
What Is zdSCADA?
zdSCADA is hosted SCADA for the oilfield. It polls the electronic devices on your sites, shows the data on dashboards and maps, sends alarms and lets you send commands back to the equipment. There is no software to install in your office; it runs on the web.
The company, zdSCADA, LP, was founded in 2014 and says it serves 300+ operators across 18 states and over 40,000 locations (zdSCADA website, 2026). Quorum Software acquired it, and zdSCADA now describes itself as part of Quorum. It writes its own device drivers and says it works with gear from ABB TotalFlow, Bristol, SCADAPak, Allen Bradley and many others (zdSCADA website, 2026).
What Does zdSCADA Do Well?
We would rather tell you straight than pretend it is a bad product. It is not.
- It talks to almost anything. Its long device list, and its offer to write drivers for rare equipment, is a real edge if your sites run a mix of old and new controllers.
- It controls, not just watches. Remote valve operation, setpoint changes and support for electronic shutdown (ESD) systems are on its features page.
- Measurement history. It keeps hourly archives, configuration files and event logs, with an audit log when a reading gets corrected.
- It is hosted for you. Backups, redundancy and an annual SOC 2 audit are listed on its platform page, and it claims more than 99.9% uptime since 2014 (zdSCADA website, 2026).
- Exports. Data goes out by web API, FTP, CFX or CSV.
If that list describes what your operation needs, zdSCADA is a fair choice.
What Does a zdSCADA Site Still Need in the Field?
This is the part buyers miss. zdSCADA is the host. It connects to devices; it does not put them on the lease for you. A typical hosted SCADA site still needs:
- Instruments on the tanks, wellhead and flowline.
- An RTU, PLC or flow computer in a cabinet to read them.
- Power for that cabinet.
- A modem or radio to get the data off the site.
- Commissioning: zdSCADA’s own onboarding page names port forwarding, modem setup and protocol settings as part of the work.
zdSCADA says its team gets customers running “in days, not months.” That covers the software side. The wiring, the cabinet and the instruments are still a field job, often for a contractor. On a big facility, that is worth it. On a 3-barrel stripper well, the math rarely works.
How Does TinyPumper Compare?
| zdSCADA | TinyPumper | |
|---|---|---|
| What it is | Hosted SCADA platform that connects to your RTUs, PLCs and meters | Wireless site monitor: gateway plus sensors |
| What it watches | Whatever your connected devices report: tanks, pressures, ESD status, plunger and dyno data | Tank levels, pressures (wellhead, flowline, injection) and engine or compressor runtime |
| Remote control | Yes: valves, setpoints, shutdowns | No. It watches; it does not control |
| Field hardware | Your instruments, RTU or PLC, cabinet, power and modem | Solar gateway, radar tank sensor and pressure sensors, up to 8 sensors per gateway |
| Install | Onboarding team plus field commissioning | Your team self-installs in 8 minutes |
| Pricing | Quoted per job, not published (zdSCADA website, October 2026) | $349 per sensor, one time, then one flat rate a month per site, unlimited sensors |
| Coverage | Depends on the comms at each site | 100% continental US coverage, because we use satellite |
| If it breaks | Ask the vendor and your hardware maker | Lifetime hardware replacement |
| Trial | Ask the vendor | 60-day money-back, we pay return shipping |
When Is TinyPumper the Better Fit?
- You run conventional wells where SCADA never penciled. TinyPumper gives you roughly 99% of SCADA’s upside for about 95% less.
- Your old SCADA costs more to keep alive than it returns. Dead batteries, failed modems, a contractor every time a tag goes quiet. TinyPumper drops in where the old cabinet sat.
- Nobody on staff does controls. A sensor screws in like a lightbulb. If it breaks, we send a new one.
- You want alerts fast. Sensors report every hour and check your thresholds every 5 minutes, so an alarm goes out right away.
Producers running TinyPumper report cutting lease runs by 30 to 50 percent and catching failures days sooner. Scale does not change this: the fit is about cost per site, whether you run 50 wells or 5,000. For the bigger picture, see our oil and gas SCADA guide and oil well monitoring systems.
TinyPumper watches tanks, pressures and runtime on one gateway. $349 per sensor, one time, then one flat rate a month per site. 60-day money-back.
See TinyPumperWhen Is zdSCADA the Better Fit?
Pick zdSCADA, or hosted SCADA like it, when you need to act from the office and not just know:
- Facilities with emergency shutdowns and remote valves.
- Sites full of existing RTUs and flow computers you want on one screen.
- Gas measurement where hourly archives and audit trails matter.
TinyPumper will not shut in a well or move a setpoint. If that is the job, it is the wrong tool, and we would rather you know now.
What TinyPumper Is, in Plain Facts
TinyPumper is remote well monitoring for oil and gas producers. It gives 100% continental US coverage because we use satellite. It connects up to 8 sensors per gateway. It comes with a 60-day money-back guarantee. All equipment has lifetime replacement. TinyPumper is the sister product of GreaseBook, the oil production software used by 600+ production companies, and its readings flow into the GreaseBook dashboard.
Quick Answers on zdSCADA Searches
- zdscada / zd scada / zd scada system: the same product, hosted oilfield SCADA. People spell it with and without the space.
- zdscada lp: zdSCADA, LP is the company behind it, founded in 2014 and based in Tyler, Texas.
- quorum zdscada / zdscada quorum: Quorum Software bought zdSCADA, and the product is now sold as part of Quorum.
- zdscada app: zdSCADA has apps on the Apple App Store and Google Play for checking sites and alarms from a phone.
- zdscada login / www.zdscada.com: existing zdSCADA customers log in through www.zdscada.com. We cannot help with their accounts; their support team can.
- zdscada camera system for oil field: the zdSCADA pages we reviewed describe telemetry, alarms and control, not cameras. TinyPumper does not sell cameras either.
- zdscada alternative reddit: the r/SCADA forum has threads asking for alternatives. Most answers there are about general industrial SCADA. For a conventional lease, the real choice is usually hosted SCADA versus a wireless monitor like TinyPumper.
Who This Page Is Not For
This page is not for producers who need remote control, shutdowns or custody-grade measurement on instrumented facilities. Stay with SCADA. It is also not a guide to every option; see oilfield monitoring alternatives and our Ignition SCADA alternative page.
Frequently Asked Questions
What is zdSCADA?
zdSCADA is a cloud-hosted SCADA platform built for oil and gas. It connects to the RTUs, PLCs, meters and controllers on your sites, shows their data on web dashboards and maps, sends alarms and lets you control equipment remotely. Founded in 2014, the company says it serves 300+ operators in 18 states (zdSCADA website, 2026). It is now part of Quorum Software.
Is zdSCADA owned by Quorum?
Yes. Quorum Software acquired zdSCADA, LP, and zdSCADA now describes itself as part of Quorum. Quorum sells it alongside its production operations software, so manual pumper data and haul tickets can flow through Quorum’s tools. If you already run Quorum’s suite, that tie-in may matter to you. If you do not, weigh zdSCADA on its own SCADA features.
What is the best zdSCADA alternative?
It depends on the job. If you need remote control and shutdowns, another hosted SCADA platform is the alternative. If you only need to see tank levels, pressures and runtime, a wireless monitor fits better. TinyPumper covers all three on one gateway, your team self-installs it in 8 minutes, and you pay one flat monthly rate per site.
Does TinyPumper control wells the way zdSCADA does?
No. TinyPumper watches; it does not control. It will not shut in a well, open a valve or change a setpoint. It tells you the moment a tank, pressure or compressor crosses a line you set, checking every 5 minutes. For most conventional leases that is what matters. For facilities that need shutdowns, stay with SCADA.
How is TinyPumper priced compared with hosted SCADA?
TinyPumper is $349 per sensor, one time. Then one flat rate a month per site, with unlimited sensors at that site. There is no RTU cabinet, no electrician and no integrator to pay. zdSCADA does not publish prices and quotes each job (zdSCADA website, October 2026), and your site hardware is a separate cost on top.